500W Single Output With PFC Function

.LOW COST, HIGH RELIABILITY .COMPACT SIZE, LIGHT WEIGHT
.COOLING FAN ON/OFF AUTOMATICALLY .100% FULL LOAD BURN-IN TEST
.BUILT IN REMOTE CONTRAL .105ºC  OUTPUT CAPACITOR
.INTERNATIONAL AC INPUT RANGE .BUILT IN EMI FILTER, LOW RIPPLE NOISE
.HIGH EFFICIENCY, LOW WORKING TEMPERATURE .BUILT IN PFC CIRCUIT
.SOFT-START CIRCUIT, LIMITING AC SURGE CURRENT
.SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE, OVER TEMP. PROTECTED
MODEL
SPECIFICATION
SM-P500-12 SM-P500-13.5 SM-P500-15 SM-P500-24 SM-P500-27 SM-P500-48
DC OUTPUT VOLTAGE 12V 13.5V 15V 24V 27V 48V
OUTPUT V. TOLERANCE ±1% ±1% ±1% ±1% ±1% ±1%
OUTPUT RATED CURRENT 40A 36A 32A 20A 18A 10A
OUTPUT CURRENT RANGE 0-40A 0-36A 0-32A 0-20A 0-18A 0-10A
RIPPLE & NOISE 240mVp-p 240mVp-p 240mVp-p 240mVp-p 200mVp-p 300mVp-p
LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
LOAD REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
DC OUTPUT POWER 480W 486W 480W 480W 486W 480W
EFFICIENCY 84% 84% 83% 85.5% 86.5% 87%
DC VOLTAGE ADJ. 10-13.2V 12-15V 13.5-18V 20-26.4V 24-30V 41-56V
INPUT VOLTAGE RANGE 88~264VAC  47~63Hz;  124~370VDC
AC CURRENT 7A/115V  3.5A/230V
POWER FACTOR 0.95/100~240VAC
INRUSH CURRENT 18A/115V  36A/230V
LEAKAGE CURRENT <3.5mA/240VAC
OVERLOAD PROTECTION 105%~135%  TYPE:FOLDBACK CURRENT LIMITING  RESET:AUTO RECOVERY
OVER VOLTAGE PROTECTION 13.8~16.2V 15.5~18.2V 18~21V 27.6~32.4V 31~36.5V 57.6~67.2V
FAN CONTROL, O.T.P. RTH1 or RTH2>=50ºC  FAN ON, <=45ºC  FAN OFF, >=70ºC  OUTPUT SHUTDOWN
TEMP. COEFFICIENT ±0.03% / ºC  (0~50ºC)
SETUP, RISE, HOLD UP TIME 1.5s, 50ms, 20ms
VIBRATION 10~500Hz, 2G  10min./1cycle, PERIOD FOR 60min. EACH AXES
WITHSTAND VOLTAGE I/P-O/P:3KVAC  I/P-FG:1.5KVAC  O/P-FG:0.5KVAC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:500VDC / 100M Ohms
WORKING TEMP., HUMIDITY -10ºC~+50ºC(REFER TO OUTPUT DERATING CURVE), 20%~90% RH 
STORAGE TEMP., HUMIDITY -20ºC~+85ºC, 10%~95% RH
DIMENSION 185*20*93mm  CASE:910
WEIGHT 1.8Kgs
SAFETY STANDARDS ---
EMC STANDARDS ---
NOTE : 1.ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25ºC  70% RH. AMBIENT.
2.TOLERANCEGINCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION.
3.RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR.
4.LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD.
5.LOAD REGULATION IS MEASURED FROM 0% TO 100% RATED LOAD.
6.C3,4,14,16,31,32,101,102 MUST BE REMOVED.
7.REFER TO OUTPUT DERATING CURVE VS INPUT VOLTAGE.

http://www.nahua.com.tw