150W Single Output Switching Power Supply

.LOW COST, HIGH RELIABILITY .COMPACT SIZE, LIGHT WEIGHT 906.gif (12301 bytes)
.105J OUTPUT CAPACITOR .100% FULL LOAD BURN-IN TEST
.INTERNATIONAL AC INPUT RANGE .BUILT IN EMI FILTER, LOW RIPPLE NOISE
.HIGH EFFICIENCY, LOW WORKING TEMPERATURE
.SOFT-START CIRCUIT, LIMITING AC SURGE CURRENT
.SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE PROTECTED
MODEL
SPECIFICATION
SM-S150-5 SM-S150-7.5 SM-S150-9 SM-S150-12 SM-S150-13.5 SM-S150-15 SM-S150-24 SM-S150-27 SM-S150-48
DC OUTPUT VOLTAGE 5V 7.5V 9V 12V 13.5V 15V 24V 27V 48V
OUTPUT V. TOLERANCE ±2% ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1%
OUTPUT RATED CURRENT 30A 20A 16.7A 12.5A 11.2A 10A 6.5A 5.6A 3.2A
OUTPUT CURRENT RANGE 0-30A 0-20A 0-16.7A 0-12.5A 0-11.2A 0-10A 0-6.5A 0-5.6A 0-3.2A
RIPPLE & NOISE    (p-p) 150mV 150mV 180mV 180mV 180mV 180mV 240mV 240mV 240mV
LINE REGULATION ±0.5% ±0.5% ±0.3% ±0.3% ±0.3% ±0.3% ±0.2% ±0.2% ±0.2%
LOAD REGULATION ±0.5% ±0.5% ±0.3% ±0.3% ±0.3% ±0.3% ±0.2% ±0.2% ±0.2%
DC OUTPUT POWER 150W 150W 150.3W 150W 151.2W 150W 156W 151.2W 153.6W
EFFICIENCY 78% 80% 80% 82% 83% 84% 85% 86% 87%
DC VOLTAGE ADJ. 4.5-5.5V 6-8.3V 8-10.4V 10.6-13.2V 12-15V 13.5-16.5V 21-28V 24-30V 43-53V
INPUT VOLTAGE RANGE 88~132VAC / 176~264VAC  SELECTED BY SWITCH  47~63Hz;  248~370VDC
AC CURRENT 3.2A/115V  1.6A/230V
INRUSH CURRENT COLD START  35A
LEAKAGE CURRENT <3.5mA/240VAC
OVERLOAD PROTECTION 105%~150%  TYPE:OUTPUT SHUTDOWN  RESET:RECYCLE AC ON / OFF
OVER VOLTAGE PROTECTION 115%~135% 125%~145% 115%~135%
OVER TEMP. PROTECTION ----------
TEMP. COEFFICIENT ±0.03% / J (0~50J)
SETUP, RISE, HOLD UP TIME 100ms, 50ms, 20ms
VIBRATION 10~500Hz, 2G  10min./1cycle, PERIOD FOR 60min. EACH AXES
WITHSTAND VOLTAGE I/P-O/P:3KVAC  I/P-FG:1.5KVAC  O/P-FG:0.5KVAC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:500VDC / 100M[
WORKING TEMP., HUMIDITY -10J~+60J(REFER TO OUTPUT DERATING CURVE), 20%~90% RH 
STORAGE TEMP., HUMIDITY -20J~+85J, 10%~95% RH
DIMENSION 199*110*50mm
WEIGHT 0.8Kgs
NOTEG 1.ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25J  70% RH. AMBIENT.
2.TOLERANCEGINCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION.
3.RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR.
4.LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD.
5.LOAD REGULATION IS MEASURED FROM 0% TO 100% RATED LOAD.
6.C2,3,11 MUST BE REMOVED.

http://www.nahua.com.tw